top of page

PRODUCT DETAILS

Description

M5Core2is the second generation core device in the M5Stack development kit series, which further enhances the functions of the original generation of cores.

The MCU is anmodel D0WDQ6-V3 and has dual core Xtensa® 32-bit 240Mhz LX6 processors that can be controlled separately. Wi-Fi are supported as standard and it includes an on board 16MB Flash and 8MB PSRAM, USB TYPE-C interface for charging, downloading of programs and serial communication, a 2.0-inch integrated capacitive touch screen, and a built-in vibration motor.

M5Core2 also features a built-in RTC module which can provide accurate timing. The power supply is managed by an AXP192 power management chip, which can effectively control the power consumption of the base and a built-in green LED power indicator helps to notify the user of battery level. The battery capacity has been upgraded to 390mAh, which can power the core for much longer than the previous model.

The M5Core2 retains the TF-card(microSD) slot and speakers. However, in order to ensure higher quality sound output, the I2S digital audio interface power amplifier chip is used to effectively prevent signal distortion. There are independent power and reset buttons on the left side and bottom of the base.

The 3 icons on the front of the screen are capacitive buttons which are programmable. There is a small expansion board on the back of the base with a 6-axis IMU sensor and microphone. The development platform and programming language supported by M5Stack Core2: Arduino,(using Blockly, MicroPython language) No matter what level of your development and programming skills, M5Stack will help You gradually turn your ideas into reality.

Power Management

Operations:
Power on: One click the power button on the left
Power off: Long press the left power button for 6 seconds
Reset: Click the RST button on the bottom side

USB drive

Before using, please go toto download the USB driver that matches your operating system, and install it.
Note:Core2currently has two CP2104/CH9102F A USB chip version, users can install the drivers (CH9102andCP210x) that are compatible with two ICs at the same time to ensure that the device drivers work normally.

Extensions

To stack M5Core2 with M5 modules, you need to remove/eliminate the battery bottom of Core2; If you wish to keep I2S Mic, IMU and Battery functions, ais required.**The CP2104 chip interface is reserved on the PCB of CORE2 to interface with the lithium battery.

The vibration sensor of M5Core2 and M5 Base series are incompatible in mechanical design. Please do not stack them together.

Product Features

  • ESP32-based, built-in Wi-Fi

  • 16M Flash,8M PSRAM

  • Built-in speaker, power indicator, vibration motor, RTC, I2S amplifier, capacitive touch screen, power button, reset button

  • TF card slot (16G Maximum size)

  • Built-in lithium battery, equipped with power management chip

  • Independent small board built-in 6-axis IMU, PDM microphone

  • M-Bus Socket & Pins

  • Compatible with multi-platform development:

Include

  • 1x M5Stack Core2

  • 1x Type-C USB(20cm)

Applications

  • Internet of things terminal controller

  • Stem education product

  • DIY creation

  • Smart home equipment

Specification


Resources

Parameter

ESP32-D0WDQ6-V3

240MHz dual core, 600 DMIPS, 520KB SRAM, Wi-Fi

Flash

16MB

PSRAM

8MB

Input Voltage

5V @ 500mA

Interface

TypeC x 1, GROVE(I2C+I/0+UART) x 1

IPS LCD Screen

2.0"@320*240 ILI9342C

Touch Screen

FT6336U

Speaker amplifier

NS4168

LED

Green power indicator light

Button

Power button, RST button, Virtual screen button*3

Vibration reminder

Vibration motor

MIC

SPM1423

I2S Power Amplifier

NS4168

6-axis IMU

MPU6886

RTC

BM8563

PMU

AXP192

USB Chip

CP2104/CH9102F (two chip versions, there is no difference in function and use)

DC-DC Boost

SY7088

TF card slot

16G Max

Lithium Battery

390mAh @ 3.7V

Antenna

2.4G 3D antenna

Operating temperature

0°C to 60°C

Base screw specifications

Hexagon socket countersunk head M3

Internal PCB board reserved interface

Battery interface (specification: 1.25mm-2P)
USB line interface (specification: 1.25mm-4P)

Net Weight

52g

Gross Weight

70g

Product Size

54 x 54 x 16mm

Package Size

75 x 60 x 20mm

Case Material

Plastic ( PC )

LEARN AND DOCUMENTS

This tutorial will show you how to control M5Core2 devices through the UIFlow graphical programming platform
This tutorial will show you how to program and control M5Core2 devices through Arduino IDE
This tutorial will show you how to control M5Core2 devices through Micropython programming
Health monitoring using the M5Stack Mini Heart Rate Unit and Non-Contact Infrared Thermometer Unit and the Waylay IO IoT platform.
I made one-wheel balancing robot. This robot can be operated remotely from a smartphone using Blynk.
Modern times make modern solutions possible. Therefore, the step to a digital snow globe is not that far.
Developing a simple remote for my openhab, I have got the app but do not want to unlock my ph

ערכת פיתוח רשמית של Core2 ESP32 Iot

מק"ט: c0a00ee2-1796-4441-b53b-92ebb3e50d5a
53.49 ₪מחיר
    • LinkedIn
    bottom of page